Go Back   Toyota Tundra Forums : Tundra Solutions Forum > Technical & Vehicle Assistance Forums > Brakes
Reload this Page Toyota Brake Specifications
Register Blogs FAQ Members List Social Groups Calendar Search Today's Posts Mark Forums Read



Readylift.com
Handy Toyota
IPT Performance Transmissions
4WheelParts.com

Free shipping on truck accessories at AutoAnything

 
Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 01-30-2008, 07:09 AM
MEvang's Avatar
Supporter
  
My Garage
Dealer : Toyota of Cincinnati Co.
2001 Toyota Tundra
My Details
Last Online: 08-26-2009 09:37 PM
Join Date: Jul 2005
Location: Colerain
Age: 49
Posts: 1,217
Rep Power: 7
MEvang will become famous soon enough. MEvang will become famous soon enough.
MEvang's Photo Albums
Default Toyota Brake Specifications
I'm starting this thread as a quick reference spot for Toyota Brake specifications. I'll start off with the Tundra and add a few now and then.
If you have a request for a certain model please chime in and I'll get it for you.
Also if you have any question about a specification please ask.
Most of these will come from Motors Information Systems 1977-2007 Disc & Drum Brake Specification and Bleeding Sequence Guide.
Mike
__________________
“The significant problems we have cannot be solved at the same level of thinking with which we created them” (Albert Einstein)
Moderator Brake Forum
Reply With Quote


  #2 (permalink)  
Old 01-30-2008, 07:14 AM
MEvang's Avatar
Supporter
  
My Garage
Dealer : Toyota of Cincinnati Co.
2001 Toyota Tundra
My Details
Last Online: 08-26-2009 09:37 PM
Join Date: Jul 2005
Location: Colerain
Age: 49
Posts: 1,217
Rep Power: 7
MEvang will become famous soon enough. MEvang will become famous soon enough.
MEvang's Photo Albums
Default Re: Toyota Brake Specifications Tundra 00-06
Tundra: 2000- 2006
Front Brakes

Calipers: Four Piston Fixed

Caliper to Upright Torque: 90 lbft

Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0028"

Normal Thickness: 1.102"

Minimum Machining: Not Specified by Manufacture

Discard at or Under: 1.024"

Finish Microinch: Not Specified by Manufacture

Rear Brakes

Type : Drum

Runout Limit: Not Specified by Manufacture

Nominal Diameter: 11.614"

Maximum Machining: 11.693"

Wheel Nut Torque: 83 lbft

Brake Bleeding Sequence: None Specified
__________________
“The significant problems we have cannot be solved at the same level of thinking with which we created them” (Albert Einstein)
Moderator Brake Forum
Reply With Quote
  #3 (permalink)  
Old 01-31-2008, 07:37 AM
MEvang's Avatar
Supporter
  
My Garage
Dealer : Toyota of Cincinnati Co.
2001 Toyota Tundra
My Details
Last Online: 08-26-2009 09:37 PM
Join Date: Jul 2005
Location: Colerain
Age: 49
Posts: 1,217
Rep Power: 7
MEvang will become famous soon enough. MEvang will become famous soon enough.
MEvang's Photo Albums
Default Re: Toyota Brake Specifications: Sequia 01-07
Sequoia 2001- 2007

Front Brakes

Calipers: Four Piston Fixed

Caliper to Upright Torque: 90 lbft

Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0028"

Normal Thickness: 1.102"

Minimum Machining: Not Specified by Manufacture

Discard at or Under: 1.024"

Finish Microinch: Not Specified by Manufacture

Rear Brakes

Type: Disc

Calipers: Single Piston Sliding Pins

Caliper Mounting Torque: 65 lbft

Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0039"

Normal Thickness: .709"

Minimum Machining: Not Specified by Manufacture

Discard at or Under: .611"

Finish Microinch: Not Specified by Manufacture

Park Brake

Type: Drum

Nominal Diameter: 8.270"

Discard At Or Over: 8.310"

Wheel Nut Torque: 83 lbft

Bleeding Sequence: None Specified
__________________
“The significant problems we have cannot be solved at the same level of thinking with which we created them” (Albert Einstein)
Moderator Brake Forum
Reply With Quote
  #4 (permalink)  
Old 02-01-2008, 07:15 AM
MEvang's Avatar
Supporter
  
My Garage
Dealer : Toyota of Cincinnati Co.
2001 Toyota Tundra
My Details
Last Online: 08-26-2009 09:37 PM
Join Date: Jul 2005
Location: Colerain
Age: 49
Posts: 1,217
Rep Power: 7
MEvang will become famous soon enough. MEvang will become famous soon enough.
MEvang's Photo Albums
Default Re: Toyota Brake Specifications: Tacoma Prerunner '07
Tacoma: 2WD 4WD and Prerunner 2007

Front Brakes

Calipers: Not Given

Caliper to Upright Torque: Caliper Bolts 2WD except Prerunner, 27lbft – 2WD Prerunner, 4WD Caliper Bolts 90 lbft; 2WD ex. Prerunner caliper bolts 80 lbft

Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0020"

Normal Thickness: 2WD .984”
4WD & Prerunner 1.102”

Minimum Machining: Not Specified by Manufacture

Discard at or Under: 2WD .906”
4WD & Prerunner 1.024”

Finish Microinch: Not Specified by Manufacture

Rear Brakes

Type: Drum

Runout Limit: Not Specified by Manufacture

Nominal Diameter: 10.00"

Maximum Machining: Not Specified by Manufacture

Discard at or Over: 10.079”

Wheel Nut Torque: 83 lbft

Special Bleeding Procedures:
1. Bleed the wheel brakes, no sequence given.
2. After bleeding air from the brakes system, if the height or feel of the brake pedal cannot be obtained, bleed air from actuator assembly using Hand-held tester by following steps below.
A. Depress the brake pedal more then 20 times with engine off.
B. Connect Hand-held tester to the DLC3
C. Turn ignition switch to the ON position
D. Select "Air Bleeding"
E. Bleed the air by following the steps displayed on the Hand- held tester
__________________
“The significant problems we have cannot be solved at the same level of thinking with which we created them” (Albert Einstein)
Moderator Brake Forum
Last edited by MEvang; 02-01-2008 at 07:35 AM.
Reply With Quote
  #5 (permalink)  
Old 02-01-2008, 07:22 AM
MEvang's Avatar
Supporter
  
My Garage
Dealer : Toyota of Cincinnati Co.
2001 Toyota Tundra
My Details
Last Online: 08-26-2009 09:37 PM
Join Date: Jul 2005
Location: Colerain
Age: 49
Posts: 1,217
Rep Power: 7
MEvang will become famous soon enough. MEvang will become famous soon enough.
MEvang's Photo Albums
Default Re: Toyota Brake Specifications: Tacoma, Prerunner '06
Tacoma: 2WD 4WD and Prerunner 2006

Front Brakes

Calipers: 2WD except Prerunner: Single Piston Sliding Pins
4WD and Prerunner 4 Piston Fixed

Caliper to Upright Torque: Caliper Bolts 2WD except Prerunner, 27lbft – 2WD Prerunner, 4WD Caliper Bolts 90 lbft; 2WD ex. Prerunner caliper bolts 80 lbft

Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0020"

Normal Thickness: 2WD .987”
4WD & Prerunner 1.102”

Minimum Machining: Not Specified by Manufacture

Discard at or Under: 2WD .906”
4WD & Prerunner 1.024”

Finish Microinch: Not Specified by Manufacture

Rear Brakes

Type: Drum

Runout Limit: Not Specified by Manufacture

Nominal Diameter: 10.00"

Maximum Machining: 10.079”

Wheel Nut Torque: 85 lbft

Special Bleeding Procedures:
1. Bleed the wheel brakes, no sequence given.
2. After bleeding air from the brakes system, if the height or feel of the brake pedal cannot be obtained, bleed air from actuator assembly using Hand-held tester by following steps below.
A. Depress the brake pedal more then 20 times with engine off.
B. Connect Hand-held tester to the DLC3
C. Turn ignition switch to the ON position
D. Select "Air Bleeding"
E. Bleed the air by following the steps displayed on the Hand- held tester
__________________
“The significant problems we have cannot be solved at the same level of thinking with which we created them” (Albert Einstein)
Moderator Brake Forum
Last edited by MEvang; 02-01-2008 at 07:34 AM.
Reply With Quote
  #6 (permalink)  
Old 02-18-2008, 07:31 AM
MEvang's Avatar
Supporter
  
My Garage
Dealer : Toyota of Cincinnati Co.
2001 Toyota Tundra
My Details
Last Online: 08-26-2009 09:37 PM
Join Date: Jul 2005
Location: Colerain
Age: 49
Posts: 1,217
Rep Power: 7
MEvang will become famous soon enough. MEvang will become famous soon enough.
MEvang's Photo Albums
Default Re: Toyota Brake Specifications: Highlander 2001-2006
Highlander: 2001-2006

Front Brakes

Calipers: Single Piston Sliding PIns

Caliper Torque: Caliper Pin Bolts 25 ftlb
Bracket to Upright Bolts 79 lbft

Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0020"

Normal Thickness: 1.102”

Minimum Machining: Not Specified by Manufacture

Discard at or Under: 1.024”

Finish Microinch: Not Specified by Manufacture

Rear Brakes

Type: Disc

Calipers: Single Piston Sliding Pins

Caliper Torque: Caliper Pin Bolts 25 lbft (32 lbft 05-06)
Bracket to Upright Bolts 44 lbft (58 lbft 05-06)


Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0059"

Normal Thickness: .433”

Minimum Machining: Not Specified by Manufacture

Discard at or Under: .390”

Finish Microinch: Not Specified by Manufacture

Park Brake

Type: Drum

Nominal Diameter: 6.690"

Discard At Or Over: 6.730"

Wheel Nut Torque: 76 lbft

Special Bleeding Procedures:
1. Bleed the wheel brakes, no sequence given.
2. After bleeding air from the brakes system, if the height or feel of the brake pedal cannot be obtained, bleed air from actuator assembly using Hand-held tester by following steps below.
A. Depress the brake pedal more then 20 times with engine off.
B. Connect Hand-held tester to the DLC3
C. Turn ignition switch to the ON position
D. Select "Air Bleeding"
E. Bleed the air by following the steps displayed on the Hand- held tester
__________________
“The significant problems we have cannot be solved at the same level of thinking with which we created them” (Albert Einstein)
Moderator Brake Forum
Last edited by MEvang; 02-19-2008 at 06:58 AM.
Reply With Quote
  #7 (permalink)  
Old 02-19-2008, 07:04 AM
MEvang's Avatar
Supporter
  
My Garage
Dealer : Toyota of Cincinnati Co.
2001 Toyota Tundra
My Details
Last Online: 08-26-2009 09:37 PM
Join Date: Jul 2005
Location: Colerain
Age: 49
Posts: 1,217
Rep Power: 7
MEvang will become famous soon enough. MEvang will become famous soon enough.
MEvang's Photo Albums
Default Re: Toyota Brake Specifications: Highlander 2007-
Highlander: 2007-

Front Brakes

Calipers: Single Piston Sliding PIns

Caliper to Upright Torque: Caliper Pin Bolts 25 ftlb
Bracket to Upright Bolts 79 lbft

Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0020"

Normal Thickness: 1.102”

Minimum Machining: Not Specified by Manufacture

Discard at or Under: 1.024”

Finish Microinch: Not Specified by Manufacture

Rear Brakes

Type: Disc

Calipers: Single Piston Sliding Pins

Caliper to Upright Torque: Caliper Pin Bolts 32 lbft
Bracket to Upright Bolts 58 lbft

Maximum Parallel
Variation: Not Specified by Manufacture

Runout Limit: .0059"

Normal Thickness: .394”

Minimum Machining: Not Specified by Manufacture

Discard at or Under: .355”

Finish Microinch: Not Specified by Manufacture

Park Brake

Type: Drum

Nominal Diameter: 7.48"

Discard At Or Over: 7.52"

Wheel Nut Torque: 76 lbft

Special Bleeding Procedures:
1. Bleed the wheel brakes, no sequence given.
2. After bleeding air from the brakes system, if the height or feel of the brake pedal cannot be obtained, bleed air from actuator assembly using Hand-held tester by following steps below.
A. Depress the brake pedal more then 20 times with engine off.
B. Connect Hand-held tester to the DLC3
C. Turn ignition switch to the ON position
D. Select "Air Bleeding"
E. Bleed the air by following the steps displayed on the Hand- held tester
__________________
“The significant problems we have cannot be solved at the same level of thinking with which we created them” (Albert Einstein)
Moderator Brake Forum
Reply With Quote
Reply

« 2004 Sequoia Brake and Tire Problem (30% front brake pads left) | Brake Dust »

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


All times are GMT -5. The time now is 12:12 AM.

© Copyright 2009 All rights reserved. TundraSolutions.com.
Other trademarks and brands are the property of their respective owners.
Use of this Web site constitutes acceptance of the TundraSolutions.com User Agreement and Privacy Policy.
Custom vBulletin Skin By v7web.net