OPEN GROUP BUY: Access cab window latches - Page 3 - Toyota Tundra Forums : Tundra Solutions Forum

mustang67408 · #31 (**permalink**) 07-02-2007, 11:44 PM

Quote:

Originally Posted by RitcheyRch

Thanks for the picture. I figured that was the part we were getting. The fun part going to be trying to replace it.

All you have to do is pull back the upper door panel to access the 10mm bolts, and then unscrew the phyllips screw on the glass. Dont loose the rubber washer or when you tighten the new one , you will break the glass.

RitcheyRch · #32 (**permalink**) 07-03-2007, 01:22 AM

It looks like the part that gets replaced have pins holding them in.

Quote:

Originally Posted by mustang67408

All you have to do is pull back the upper door panel to access the 10mm bolts, and then unscrew the phyllips screw on the glass. Dont loose the rubber washer or when you tighten the new one , you will break the glass.

mustang67408 · #33 (**permalink**) 07-03-2007, 09:33 AM

Quote:

Originally Posted by RitcheyRch

It looks like the part that gets replaced have pins holding them in.

Good luck getting the pins out while in the vehicle and not scratching everything up.
Its easier to remove the whole thing, then take it apart, at least it is for me.

lewisb62 · #34 (**permalink**) 07-03-2007, 11:43 AM

I'm in too, and PM'd you.

Thanks.

njjetski · #35 (**permalink**) 07-03-2007, 01:12 PM

Im in... my kid broke one of mine... PM'ed you

trfytoy · #36 (**permalink**) 07-03-2007, 08:32 PM

Thanks guys!

I will find the easiest way to install them and make instructions, so no worries!

Josh

RitcheyRch · #37 (**permalink**) 07-04-2007, 01:39 PM

Mine have never broke so just looking for some preventive maintenance here.

trfytoy · #38 (**permalink**) 07-04-2007, 03:18 PM

Quote:

Originally Posted by RitcheyRch

Mine have never broke so just looking for some preventive maintenance here.

Ha ha, your lucky so far. Because they will. I bought my '03 used in 05 and they were already broke for me.

Josh

RitcheyRch · #39 (**permalink**) 07-04-2007, 03:27 PM

I think have been spared the luck since dont normally ever open those windows.

Quote:

Originally Posted by trfytoy

Ha ha, your lucky so far. Because they will. I bought my '03 used in 05 and they were already broke for me.

Josh

njjetski · #40 (**permalink**) 07-05-2007, 08:51 AM

Josh,
Sent you pmt today via paypal. Let me know when they are in.

Thanks.

lewisb62 · #41 (**permalink**) 07-05-2007, 01:52 PM

$35.00 payment sent to Trfytoy via Paypal.

longwoodklon · #42 (**permalink**) 07-05-2007, 04:30 PM

Quote:

Originally Posted by lewisb62

$35.00 payment sent to Trfytoy via Paypal.

Same here, just sent today.
/Mike

NuMb_FiNgErS · #43 (**permalink**) 07-09-2007, 01:17 PM

Payment sent

CHINKinatundra · #44 (**permalink**) 07-09-2007, 03:44 PM

payment sent

trfytoy · #45 (**permalink**) 07-12-2007, 12:33 AM

I stopped by the machine shop today and looks like the beginning of next week I will have the first set off the mill and test fitting them on my truck. After that they should take 2-3 days for maching and 3-5 days for anodizing. So not much longer. Thanks for everyone being so patient!

Josh