Anyone knows how to program the factory alarm

[carloslopez63]

Anyone knows how to program the factory alarm for lock and unlock the doors as soon as start the motor or turn the motor off. THANKS

[MrSmitty]

Anyone knows how to program the factory alarm for lock and unlock the doors as soon as start the motor or turn the motor off. THANKS

The only thing you can turn off/on with the VIP RS3200 Alarm is set it up so that the doors locks 0,15 or 30 seconds after the key is taken out of the ignition and all the doors are shut..

[nhparrot]

The only thing you can turn off/on with the VIP RS3200 Alarm is set it up so that the doors locks 0,15 or 30 seconds after the key is taken out of the ignition and all the doors are shut..

That is the passive arming feature. You can also set ignition controlled automatic door lock/unlock.

[MrSmitty]

Oh, cool.

[MrSmitty]

programming option allows you to set the doors to lock when when the key is turned on, and unlock when the key is turned off.

• Open the driver's door. Remove the key from the ignition switch.
  
• (Complete these steps within 30 seconds)
  
  1. Insert the key into the ignition switch.
     
  2. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  3. Turn the key from LOCK to ON 5 times, ending at ON
     (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON)
     
• Programming option (select one of the following).
  
  1. [Ignition controlled lock ON] Close the driver's door.
     
  2. [Ignition controlled lock OFF] Close the driver's door twice, leaving it closed.
     (SHUT - OPEN - SHUT)
     
• Turn the key to LOCK. The programming is complete. If programming did not occur, start over.

[koam]

Has anyone actually done this with the 3200 "PLUS"? Those instructions to lock and unlock with ignition from the data base is for the 3200 (No plus). It looks like the only option is for the passive feature with the 3200 PLUS.

Mr Smitty did it work on your truck? Thanks.

[MrSmitty]

Has anyone actually done this with the 3200 "PLUS"? Those instructions to lock and unlock with ignition from the data base is for the 3200 (No plus). It looks like the only option is for the passive feature with the 3200 PLUS.

Mr Smitty did it work on your truck? Thanks.

I was searching for that info late last night... I have NOT tried it yet..

[carloslopez63]

Thanks for the information MRSMITTY but I tried 5 times and it didnot work. I think my truck has the 3200 PLUS.

[MrSmitty]

I might have the wrong info... maybe someone who is subscribed could chime in...

The booklet that came with my RS3200 Plus system when I bought my truck did not mention anything in it but the programming of the Passive and Active controls.. but NhParrot claims there is a feature. I will find the information for you guys...

[MrSmitty]

Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entry, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.

• Open the driver's door. Remove the key from the ignition switch.
  
• (Complete these steps within 40 seconds)
  
  1. Insert the key into and remove it from the ignition switch 2 times.
     (IN - OUT - IN - OUT)
     
  2. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  3. Insert the key into and remove it from the ignition switch 1 time.
     (IN - OUT)
     
  4. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  5. Insert the key into the ignition switch and leave it in.
     
  6. Close the driver's door.
     
  7. Turn the key from LOCK to ON 4 times, ending at LOCK
     (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
     
  8. Wait for the locks to stop, then remove the key from the ignition switch.
     
• On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
  
  1. [For all doors unlock] press and release the UNLOCK button.
     
  2. [For driver door unlock] press and release the LOCK button.
     
• Open the driver's door. The programming is complete. If programming did not occur, start over.
  

The second programming option allows you to set the doors to lock when when the key is turned on, and unlock when the key is turned off.

• Open the driver's door. Remove the key from the ignition switch.
  
• (Complete these steps within 30 seconds)
  
  1. Insert the key into the ignition switch.
     
  2. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  3. Turn the key from LOCK to ON 5 times, ending at ON
     (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON)
     
• Programming option (select one of the following).
  
  1. [Ignition controlled lock ON] Close the driver's door.
     
  2. [Ignition controlled lock OFF] Close the driver's door twice, leaving it closed.
     (SHUT - OPEN - SHUT)
     
• Turn the key to LOCK. The programming is complete. If programming did not occur, start over.
  

When performing the programming, the park lights may or may not flash to confirm that the program was accepted. The only way to confirm the programming is to test them to see if they are functioning as desired.
These procedures may or may not apply to pre-2001 models.


Last Modified: 2004-01-05 Number of views: 6394

Print This Save This E-mail This Talk About This ( 28 )
Comments

Keyless entry
I just tried it on my 04 Dblcab and it worked great!!!! just had to remove the key in step H and it worked great!!!! Thanks!!
Joe [2006-01-01]
Add your comments

Step H.
First I want to say thank you, it worked great. Like what was said in one of the comments I also found out that, "step 2H, the locks don't start doing their thing until after you take the key out. So basically, take the key out, then wait for the locks to stop, then continue on with step 3. FYI"
[2005-08-06]
Add your comments

How about for a 2005 Double Cab?
Does this work for the 2005 Model as well or how about the LOCk all doors when you begin to drive anyone has the program sequence for that?
Nikko [2005-07-12]
Add your comments

play with step G for 2004 x-cab auto
1. Open the driver's door. Remove the key from the ignition switch. 2. (Complete these steps within 40 seconds) A. Insert the key into and remove it from the ignition switch 2 times. (IN - OUT - IN - OUT) B. Close, then open the driver's door 2 times. (SHUT - OPEN - SHUT - OPEN) C. Insert the key into and remove it from the ignition switch 1 time. (IN - OUT) D. Close, then open the driver's door 2 times. (SHUT - OPEN - SHUT - OPEN) E. Insert the key into the ignition switch and leave it in. F. Close the driver's door. G. Turn the key from LOCK to ON 1 times, ending at LOCK (LOCK - ON )for the first remote H. remove the key from the ignition switch Wait for the locks to stop, then. 3. On the key fob, press and release both LOCK and UNLOCK buttons at the same time. A. [For all doors unlock] press and release the UNLOCK button. B. [For driver door unlock] press and release the LOCK button. 4. Open the driver's door. The programming is complete. If programming did not occur, start over. 5. NOTE: Step G is changed for each remote you program LOCK - ON one time)for the first remote remove the key and wait for the doors to unlock,(lock-on-lock-on) two time for the second remote remove key wait for locks to stop
chuck wagon [2005-06-03]
Add your comments

I Got it.....for the 2004 x-cab
Played with the step “G” and found (lock to on) one time for the first remote, pull out key and wait. Then both buttons at the same time, then unlock (A) open door. For the second remote in step (G) do lock to on twice and it worked. Unable to get both doors open with one push of remote, but at least I have a remote again. Play with step G.
chuck wagon [2005-06-02]
Add your comments

Great!
All I can say is thanks. This worked great. I followed the instructions, and everything worked as described.
Propman07 [2005-04-24]
Add your comments

I'd love to turn off the unlock double beep
I like the lock beep, but the unlock double beep is annoying and not really necessary. I'd love to program that away.
[2004-11-24]
Add your comments

the other remote???
do you have to do this for each remote??
[2004-10-27]
Add your comments

Awesome Info.
Thanks for sharing this with everyone. it worked for my 04 taco doublecab.
[2004-09-27]
Add your comments

'04 Doublecab
Just finished this on my new '04 Doublecab. Worked great! The only difference I had was in the first programming option I had to remove the key for the locks to start. When the locks stopped (4 times) I left the key out and went on to step 3 and it was fine. Thanks again.
DaveB [2004-08-18]
Add your comments

2000 PreRunner?
Will this procedure work on a 2000 Tacoma?
[2004-08-09]
Add your comments

2004taco Keyless entry programming
second programming option worked great...the first I can't get to take...locks don't start moving in 2H until after I pull the key....ideas????
New TACO Owner [2004-07-31]
Add your comments

keyless functions
Worked perfect on my '04 double cab. Pretty neat trick.
Foy Blackmon [2004-06-07]
Add your comments

coooooool
Just did it. Worked awesome!
[2004-06-07]
Add your comments

Flowless Deployment
Really darn nice! Worked the first time I tried.
Martin [2004-05-26]
Add your comments

Woked Like A Charm!
Wow! This was easier than I thought. Both programs worked the 1st time I tried them on my 2003. I wonder if there are any other programming options floating around somewhere...
[2004-05-21]
Add your comments

Works as advertised
Awesome fix, worked perfectly on my '04
Sam [2004-03-28]
Add your comments

HELP
I tried it and it didn't work for me either. now the fob doesn't work at all....can someone help?
JASON [2004-03-03]
Add your comments

GOT IT
I finally did it. Thanks. For anyone that messes up and doesn't have functionality of the regular keyless entry... try this link first http://www.geocities.com/toyota_speed2003/add_02.html then come back to this.
[2004-03-03]
Add your comments

Nice. Thank you!
Nice feature!
[2004-03-02]
Add your comments

Thank you
Thank you for posting these intstructions... I've had my new 2004 Tacoma PreRunner TRD for 2 weeks, and was annoyed from the beginning with this feature. I used the instructions, and it worked perfectly. Now both doors unlock with the "unlock" button, as it should. Thanks
[2004-02-11]
Add your comments

minor correction
I'm not sure whether this varies for model years, but I tried this on my '04 S-Runner and I realized that for step 2H, the locks don't start doing their thing until after you take the key out. So basically, take the key out, then wait for the locks to stop, then continue on with step 3. FYI
[2004-02-08]
Add your comments

Very Spiffy
Thanks for the tech tip! Both options worked for my 2004. Where'd you find this out, anyway? Great tip.
Steve [2004-01-17]
Add your comments

excellent work! just one thing...
When you attempt the first programming option (unlock all/driver doors)... after step "2H"... WAIT for the doors to go thru their lock/unlock/beep sequence (the doors should lock and unlock 4 times or so) ONCE THEY STOP, continue to step 3. This drove me nuts as the "second programming option" was a piece of cake =)
[2004-01-05]
Add your comments

program keyless entry
This is Great!!! Worked with no problems, and I love the other info. on this forum and site.
[2003-12-06]
Add your comments

Dont work
I tired it and now the doors wont unlock at all with the key fob. The only way i can get in is unlock it manually. I tired it several times.
[2003-12-01]
Add your comments

Program keyless entry on 2004
Tried this on my 2004 Tacoma and didn't work. Any ideas? I really to change unlock to operate both doors at once.
David [2003-11-16]
Add your comments

Just awesome. thanks!!
Can't believe how easy this is to fix a common problem: Having to press your key fob twice just to get the pass side open. Fixed!!!!
[2003-10-12]

[kwazy]

I've tried this (and many other) procedures on my '05 w/ the "alarm upgrade" option, but no luck. I actually dinged toyota on the post-sale survey on this, and my local dealership service dept called me to follow up on it. After several weeks of research and exchanging emails, I was finally told that the 05 Tacoma simply does not have this capability, either with and without the upgraded alarm, and that an aftermarket alarm was the only way to accomplish this.

Still hoping someone proves them wrong...

[MrSmitty]

I've tried this (and many other) procedures on my '05 w/ the "alarm upgrade" option, but no luck. I actually dinged toyota on the post-sale survey on this, and my local dealership service dept called me to follow up on it. After several weeks of research and exchanging emails, I was finally told that the 05 Tacoma simply does not have this capability, either with and without the upgraded alarm, and that an aftermarket alarm was the only way to accomplish this.

Still hoping someone proves them wrong...

yeah the more and more I read the Information I posted, It seems the information is for 2001-04 Prerunner and Tacoma.... I guess the 05-06 Tac's with the RS3200 Plus are screwed....

[pro1tuber]

PLEASE HELP ME!! i have tried this to program a second remote... everything goes right even when i press both buttons on the new remote the doors lock and unlock a few times.but then when i try to use the remote ...nothing!!! it will not lock or unlock. what i am i missing????

[nhparrot]

PLEASE HELP ME!! i have tried this to program a second remote... everything goes right even when i press both buttons on the new remote the doors lock and unlock a few times.but then when i try to use the remote ...nothing!!! it will not lock or unlock. what i am i missing????

Are the 1st 3 characters of your existing remote FCC # BAB?

[pro1tuber]

yes they are.. the #'s on the new remote match exactly to the orig. one. they start with BAB.