Toyota Tundra Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 25 Results
  1. 1Gen-Member Mods, Build Threads, Write-ups
    It's finally time to convert my truck to a flatbed. Here we go! 2002 AC 4x4 312,XXX miles The ol girl has taken me a lot of places and seen some real shit. Time for an upgrade
  2. Body (Interior & Exterior)
    Hey everyone! Hope you are well. I have swapped out the aftermarket tail gate handle with an OEM one. I hope this one lasts longer. Here it is all broken and ugly. The handle...not me. I'm perfect. I used a star driver to get all the screws out. Then here you can see the...
  3. 1Gen-Member Mods, Build Threads, Write-ups
    Here is a video on how I replaced the seatbelt housing in my Dad's 2002 Tundra. Hope this helps someone!
  4. 1Gen-Sequoia
    Are your cup holder inserts torn, disintegrating, floppy, or missing? Restore their grip with this DIY project that can cost less than $5! Save yourself the hassle of searching online for the right part number or name and do it yourself in about two hours! No man should suffer from floppy...
  5. Midwest
    I am new on here and was wondering if someone could help me out... i have a 2012 rock warrior and was adding steering radio controls and noticed that there are now 2 ground wires but only 1 spot on the airbag to "plug into"... has anyone run into this? thanks in advance.
  6. Interior & Exterior
    Backed into a cement wall in an alley while coming out of a friends house. Driver side of the chrome bumper is slightly pushed in (not folded) and raised up. The bottom corner (where the bumper and bed meet) has paint broken and wants to flake off. Planning on taking my bumper off and using a...
  7. 1Gen-Tundra
    First step was to see if a 10" sub would fit. I thought it would after taking some measurements. Next step was to evaluate the existing storage compartment. I sealed it best I could using Peel & Seal tape from Home Depot. It's not perfect by any means, but it's a first attempt. This acts as a...
  8. 2Gen-Member Mods, Write-ups, Build Threads
    Just installed LEDs. Quick and easy. Gonna post some pics. I'm new here so learning how to navigate but I feel I have to share since I got the idea from this site here: http://www.tundrasolutions.com/forums/tundra/171790-diy-led-puddle-lights/ My pics will be similar for my 2011 Tundra CrewMax...
  9. 1Gen-Tundra
    I have a first gen 2000 v8 sr5 4x4 blah blah blah. Recently i had replaced my cv shaft after having it blow apart while off roading. wasnt able to get the cv shaft out of the diff ont he passenger side with my current tools so i had left it in. so i was driving around with no RF cv and the...
  10. 1Gen-Tundra
    I will be pulling the engine on my 2001 Tundra, 4.7 liter, 4x4. It has low miles but has rolled a rod bearing on slipped a wrist pin for no apparent reason. Its not worth trying to rebuild according to most people, so I am going to swap in a good used motor. I have a chilton's manual but it...
  11. 1Gen-Tundra
    Hello everyone, I have a 2002 tundra SR5 V-8 4wd and I CAN NOT open my driver side door key wont work power lock wont unlock it. Nothing. I cant get the door panel off because the door just wont open. I was hoping someone can tell me how I can go about fixing it. I have had no luck getting to...
  12. 1Gen-Sequoia
    So, while at SEMA last year, came across the Warrior Products booth (primarily Jeep parts) and poked around. Found these 2-inch LED backup lights - I liked the look and the inclusion of the grommets, which I figured would make for a super clean install. Warrior Products 2910 - Warrior Products...
  13. 2Gen-Tundra
    so im looking to lift my 09 DC tundra right now im sitting with bilsteins all around, top settings in the front. im planning on getting the CST 3.5 lift spindles and that would put me up around 5" total up front and im curious as to what the best method to raise the rear would be and what all i...
  14. 1Gen-Tundra
    As promised, here are my trials and tribulations from the 90k service on my 2005 4.7L V8 Access Cab with 92,000 miles. Cost: approx. $450 Time Spent: 12 hours After thoroughly researching timing belt/water pump replacement "How To's" I purchased a timing belt kit from volkstoy on ebay for...
  15. 1Gen-Tundra
    Has anyone attempted re-keying a replacement ignition lock cylinder? Locksmith quoted me $400 to replace my worn lock cylinder with one that fits the old key. I have the immobilizer option. Are there special lock smith tools and ECM tricks that I can't do? I have an '01 Sequoia - has the...
  16. 2Gen-Tundra
    I have the Magnetic Gray Metallic 2012 Tundra TRD and im thinking about either powder coating the chrome bumpers and grille surround or having it color matched. Any ideas, advice????? Thanks
  17. 2Gen-Tundra
    Hi to everybody here is my history I already install a set of hid's in my 2012 tundra everything goes perfect until i have to mount again the headlight, because there is small clip that have to seat in a small piece of metal under the headlight, I tried different ways to.set the unit but all...
  18. Suspension & Axle
    I have a 2000 2wd access cab tundra with 180k miles: one of my shocks is leaking so I need to replace it, I have stock springs/shocks with 2" revtek spacers installed. This is strictly a street truck. What replacment shocks did you use, any recomednadtions for me? At what mileage did you swap...
  19. 2Gen-Tundra
    I removed my center console and recovered it. I think it came out pretty well. Thanks to JessandJamie. Their thread was very helpful. http://www.tundrasolutions.com/forums/tundra/186110-ill-pay-you-5-if-you/ Forgot to take a before picture but the after is pretty cool.
  20. 1Gen-Tundra
    Hello! First off, I'd like to say hello to everybody. I have owned my Tundra since I bought it in 06. It is basically stock except some appearance items. Well, today I installed Bi-Xenon HID lights. I took my time and i did a pretty clean install. My wrenching aren't the best, but I...
1-20 of 25 Results
Top